Cisco eStreamer Log Collector in Exabeam Data Lake

Data Lake provides the ability for organizations to collect data from their Cisco FireSight systems. Unlike FileBeats and WIndowsBeats collectors, the eStreamer collector is a service that runs on the Data Lake host and connects to the remote servers communicating over the Cisco eStreamer protocol.

In a multi-node cluster, note that the eStreamer collector runs on the Data Lake master node exclusively. To connect to the eStreamer server, Data Lake uses eNcore version 3.7.4 service library.

Prerequisites for Setting Up Cisco eStreamer Collector

Port 8302 is opened for inbound and outbound traffic on the customer's firewall. This is the default port on which the eStreamer server runs.
client.pkcs12 file (this file is generated in the section Configure eStreamer Client)
Public IP address of the Data Lake master node
Network route between Data Lake master node and eStreamer client (such that endpoints respond to pings and allow bi-directional traffic).

Configure eStreamer Client for Data Lake

This first section generates the public-private key pair needed to run eNcore. This key pair is delivered in a pkcs12 file.

Log into eStreamer Server.
Navigate to the eStreamer integration page under System > Integration > eStreamer
Select Create Client at the top right.
You will be asked for a Hostname (required) and Password (optional).
If you choose to enter a password, then you will be required to enter the same password later in the setup process while configuring the eNcore for parsing the certificate on the client side. Please make note of this password and that it is not the login credential password.
1. Use IP of the Exabeam Site Collector (with OpenVPN configured) returned from the following command:
```
curl -s ipinfo.io/ip
```
  If no IP is returned, use the IP of the site collector (with OpenVPN configured) which appears in Data Lake Collector Management menu. Navigate to Settings > Collector Management for a listing of collectors..
2. Ensure the following port forwarding rule is added to the site collector host:
```
sudo firewall-cmd --add-forward-port=port=8302:proto=tcp:toport=8302:toaddr=<eStreamer IP >  --permanent
sudo firewall-cmd --reload
sudo firewall-cmd --list-all
```
  Note
  The above firewall add-forward rule will allow traffic to masquerade as the public IP of the site collector to the eStreamer server as if the VPN tunnel is not there. Double check this masquerade setting in the output of the list-all command.
Download the client certificate by clicking the download icon to the right of the Hostname.
On the left side of this same page select all of the event types that will be collected by the eStreamer clients and click Save.

Run eStreamer Client for Exabeam Data Lake Log Collecting

Start eStreamer Collector

Copy the certificate file that was downloaded in the section Configure eStreamer Client. In the below example, replace path with the path to where the certificate was saved.
```
scp /path/client.pkcs12 user@host:/opt/exabeam/data/lms/estreamer/client.pkcs12
```

Configure the collector and enable the estreamer.conf file. located in the /opt/exabeam/data/lms/estreamer/ directory. In the server block, edit using the proper site collector IP address (internal tunnel adapter IP) and certificate filename. (Leave the pkcs12Filepath field alone if client.pkcs12 will be overwritten.)

"servers": [
            {
                "host": "<site_collector_ip>",
                "pkcs12Filepath": "[client.pkcs12]",
                "port": 8302,
                "tls@comment": "Valid values are 1.0 and 1.2",
                "tlsVersion": 1.2
            }
        ]

You will be asked to enter the eStreamer service host (the public IP Address of the host box) as well as the password (the same certificate password you created in Step 4: of Configure eStreamer Client).
```
cd /opt/exabeam/bin/lms/ 
bash /opt/exabeam/bin/shell-environment.bash
./lms-estreamer-install
```
Start the eStreamer collector
```
cd /opt/exabeam/bin/lms
./lms-estreamer-start
```
Note
By default eStreamer will begin collecting logs from 30 days before installation. See Configure Start Time for more information on this parameter.

Stop eStreamer Collector

This stops eStreamer but does not uninstall the client.

./lms-estreamer-stop

Verify eStreamer Client Status for Exabeam Data Lake Log Collecting

Verify Health of eStreamer Collector

There is a health check for eStreamer Collector through the Health Status page in the UI. However, if the collector is NOT enabled, the Health Status page will show the client as 'Healthy'.

You can also check estreamer.log and the logs will give more detailed information about the status of the client. For example, if there are fetching errors, etc.

Verify Status of eStreamer Collector

To check the status of the service from the CLI:

./lms-estreamer-status

Uninstall Exabeam Data Lake eStreamer Log Collector

This script stops the service, disables, and removes it. You will lose all of the current states. However, this does NOT remove the certificate; if mistakes are made during install you can run this script multiple times and restart.

./lms-estreamer-uninstall

Additionally, remove the hostname and password from the eStreamer Server console.

Log into eStreamer Server.
Navigate to the eStreamer integration page under System > Integration > eStreamer.
Select the applicable eStreamer client.
Remove the Hostname and password record.

Cloud-delivered Data LakeExabeam Data Lake Collector Guide

Table of ContentsTable of Contents